- Kinzua Viaduct; Erie Railway.
Valleys and ravines are now crossed by viaducts of iron and steel, of which the Kinzua viaduct, illustrated here, is an example. A branch line from the Erie, connecting that system with valuable coal-fields, strikes the valley of the Kinzua, a small creek, about 15 miles southwest of Bradford, Pa. At the point suitable for crossing, this ravine is about half a mile wide and over 300 feet deep. At first it was proposed to run down and cross the creek at a low level by some of the devices heretofore illustrated in this article. But finally the engineering firm of Clarke, Reeves & Co. agreed to build the viaduct, shown above, for a much less sum than any other method of crossing would have cost. This viaduct was built in four months. It is 305 feet high and about 2,400 feet long. The skeleton piers were first erected by means of their own posts, and afterward the girders were placed by means of a travelling scaffold on the top, projecting over about 80 feet. No staging of any kind was used, nor even ladders, as the men climbed up the diagonal rods of the piers, as a cat will run up a tree. - Locomotive of To-day
- Gearless, 75 H.P
Gearless, 75 H.P. Gearless Transmission Co., Rochester, N. Y. PRICE: $3,750 BODY: Side entrance tonneau SEATS: 7 persons WEIGHT: 3,000 pounds WHEEL-BASE: 128 inches TREAD: 56 inches TIRES, FRONT: 36 × 4 inches TIRES, REAR: 36 × 4½ inches STEERING: Worm and nut BRAKES: On transmission and 2 on each rear hub SPRINGS: Semi-elliptical FRAME: Pressed steel BORE: 413/16 in.; STROKE: 5⅝ in. CYLINDERS: 6 vertical in front VALVE ARRANGEMENT: Inlet and exhaust in side ports MOTOR SUSPENSION: From sub-frame COOLING: Water IGNITION: Jump spark, 2 sets of plugs CURRENT SUPPLY: Storage battery and magneto CARBURETER: Float-feed LUBRICATION: Pump driven by gears MOTOR-CONTROL: Spark and throttle CLUTCH: Expanding ring CHANGE GEAR: Gearless 1907 model, direct drive SPEEDS: 2 forward and reverse CHANGE-GEAR CONTROL: Foot pedal for forward speeds; side lever for back up DRIVE: Shaft - Hercules, Model 101
Hercules, Model 101. James Macnaughtan Co., Buffalo, N. Y. PRICE: $2,000 BODY: Closed delivery wagon CAPACITY: 1,000 pounds WEIGHT: 2,700 pounds TIRES, FRONT: 34 × 2 inches TIRES, REAR: 36 × 2 inches STEERING: Horizontal side lever BRAKES: Internal expanding hub SPRINGS: Front, half platform; rear, full elliptical MOTORS: Single equipment MOTOR SUSPENSION: From body MOTOR-CONTROL: Westinghouse CHANGE SPEEDS: 4 forward and reverse DRIVE: Double chain - Frontenac, Model C, 40 H.P
Frontenac, Model C, 40 H.P. Abendroth & Root Mfg. Co., Newburgh, N. Y. PRICE: $3,500 BODY: Side entrance tonneau SEATS: 5 to 7 persons WEIGHT: 2,800 pounds WHEEL-BASE: 123 inches TREAD: 56 inches TIRES, FRONT: 34 × 4 inches TIRES, REAR: 34 × 4½ inches STEERING: Bevel gear connecting to worm and nut BRAKES: Internal and external on rear wheels BORE: 4¾ in.; STROKE: 5 in. SPRINGS: Semi-elliptical FRAME: Pressed steel CYLINDERS: 4, vertical in pairs VALVE ARRANGEMENT: On same side MOTOR SUSPENSION: From sub-frame COOLING: Water, fin tube radiator IGNITION: Jump spark CURRENT SUPPLY: Storage battery and magneto CARBURETER: Automatic LUBRICATION: Splash MOTOR-CONTROL: Spark and throttle CHANGE GEAR: Sliding type SPEEDS: 3 forward and reverse CHANGE-GEAR CONTROL: Selective system DRIVE: Shaft - Gearless, 50 H.P
Gearless, 50 H.P. Gearless Transmission Co., Rochester, N. Y. PRICE: $3,000 BODY: Side entrance tonneau SEATS: 5 persons WEIGHT: 2,600 pounds WHEEL-BASE: 124 inches TREAD: 56 inches TIRES, FRONT: 36 × 4 inches TIRES, REAR: 36 × 4 inches STEERING: Worm and nut BRAKES: On transmission and two on each rear hub SPRINGS: Semi-elliptical FRAME: Pressed steel BORE: 4⅝ in.; STROKE: 5 in. CYLINDERS: 4, vertical in front; two cycle MOTOR SUSPENSION: From sub-frame COOLING: Air jackets. Blower; copper fins cast on cylinders IGNITION: Jump spark CURRENT SUPPLY: Storage battery and dry cells CARBURETER: Float-feed LUBRICATION: Mechanical force feed oiler MOTOR-CONTROL: Spark and throttle CLUTCH: Expanding ring CHANGE GEAR: Gearless 1907 model, direct drive SPEEDS: 2 forward and reverse CHANGE-GEAR CONTROL: Foot pedal for forward speeds; ride lever for reverse DRIVE: Shaft - Gearless, 60 H.P
Gearless, 60 H.P. Gearless Transmission Co., Rochester, N. Y. PRICE: $3,250 BODY: Side entrance tonneau SEATS: 5 persons WEIGHT: 2,800 pounds WHEEL-BASE: 124 inches TREAD: 56 inches TIRES, FRONT: 36 × 4 inches TIRES, REAR: 36 × 4 inches STEERING: Worm and nut BRAKES: On transmission and rear hubs SPRINGS: Semi-elliptical FRAME: Pressed steel BORE: 5 in.; STROKE: 5 in. CYLINDERS: 4 vertical in front, 2 cycle MOTOR SUSPENSION: From sub-frame COOLING: Water IGNITION: Double jump spark CURRENT SUPPLY: Magneto and battery CARBURETER: Float-feed LUBRICATION: Mechanical force feed MOTOR-CONTROL: Spark and throttle CLUTCH: Expanding ring CHANGE GEAR: Gearless direct drive SPEEDS: 2 forward and reverse CHANGE-GEAR CONTROL: Side lever and foot pedal DRIVE: Shaft - Covert Commercial Car, 12 H.P
Covert Commercial Car, 12 H.P. Covert Motor Vehicle Co., Lockport, N. Y. PRICE: $1,000 BODY: Express (screen sides) CAPACITY: 1,000 pounds WEIGHT: 1,500 pounds WHEEL-BASE: 84 inches TREAD: 56 inches TIRES, FRONT: 32 × 2 inches TIRES, REAR: 32 × 2 inches SPRINGS: Full elliptic CYLINDERS: Double opposed MOTOR SUSPENSION: From side members of frame, under seat COOLING: Water; cellular radiator IGNITION: Jump spark CURRENT SUPPLY: Batteries CHANGE GEAR: Sliding type CHANGE-GEAR CONTROL: Side lever DRIVE: Shaft and bevel gears - Frontenac Runabout, Model D, 40–45 H.P
Frontenac Runabout, Model D, 40–45 H.P. Abendroth and Root M'f'g. Co., Newburgh, N. Y. PRICE: $3,500 BODY: Runabout SEATS: 3 persons WEIGHT: 2,500 pounds WHEEL-BASE: 123 inches TREAD: 56 inches TIRES, FRONT: 36 × 3½ in. TIRES, REAR: 36 × 4½ in. STEERING: Bevel gear and shaft connecting to worm and nut BRAKES: External and internal on rear wheels SPRINGS: Semi-elliptical FRAME: Pressed steel BORE: 4¾ in.; STROKE: 5 in. CYLINDERS: 4 vertical, in pairs VALVE ARRANGEMENT: On one side MOTOR SUSPENSION: Sub-frame COOLING: Water; fin tube radiator IGNITION: Jump spark (double) CURRENT SUPPLY: Magneto and battery CARBURETER: Automatic float-feed LUBRICATION: Splash MOTOR-CONTROL: Spark and throttle CHANGE GEAR: Sliding type SPEEDS: 3 forward and reverse CHANGE-GEAR CONTROL: Selective system DRIVE: Shaft - Chicago Coal or Gravel Truck
Chicago Coal or Gravel Truck. Chicago Commercial Auto Mfg. Co., Chicago, Ill. BODY: Tilting CAPACITY: 5 tons WHEEL-BASE: 126 inches TREAD: 64 inches TIRES, FRONT: 36 inches, solid rubber TIRES, REAR: 36 inches, solid rubber BRAKES: On transmission shaft and rear hubs SPRINGS: Platform type FRAME: Steel BORE: 6 inches STROKE: 6 inches CYLINDERS: 4, cast separate VALVE ARRANGEMENT: in cylinder heads on same side MOTOR SUSPENSION: Under seat COOLING: Water IGNITION: Jump spark CURRENT SUPPLY: Batteries or magneto CARBURETER: Float-feed type LUBRICATION: Mechanical force feed MOTOR-CONTROL: Spark and throttle CLUTCH: Cast steel bands with graphite inserts CHANGE GEAR: Sliding type SPEEDS: 3 forward and reverse CHANGE-GEAR CONTROL: Side lever DRIVE: Side chains - Chicago Combination Pass. & Bagg. Car
Chicago Combination Pass. & Bagg. Car. Chicago Commercial Auto Mfg. Co., Chicago, Ill. BODY: Passenger and baggage car SEATS: 16 persons WHEEL-BASE: 126 inches TREAD: 64 inches TIRES, FRONT: 36 inches, solid rubber TIRES, REAR: 36 inches, solid rubber BRAKES: On transmission shaft and rear wheels SPRINGS: Platform type FRAME: Steel BORE: 6 inches STROKE: 6 inches CYLINDERS: 4 vertical, separate VALVE ARRANGEMENT: In cylinder heads, on same side MOTOR SUSPENSION: Under seat COOLING: Water IGNITION: Jump spark CURRENT SUPPLY: Batteries or magneto CARBURETER: Float-feed LUBRICATION: Mechanical force feed MOTOR-CONTROL: Spark and throttle CLUTCH: Cast steel band with graphite inserts CHANGE GEAR: Sliding type SPEEDS: 3 forward and reverse CHANGE-GEAR CONTROL: Side lever DRIVE: Side chains - Chicago Truck with Winch
Chicago Truck with Winch. Chicago Commercial Auto Mfg. Co., Chicago, Ill. BODY: Platform truck with winch CAPACITY: 5 tons WHEEL-BASE: 126 inches TREAD: 64 inches TIRES, FRONT: 36 inches, solid rubber TIRES, REAR: 36 inches, solid rubber STEERING: Vertical column BRAKES: On transmission and rear hubs SPRINGS: Platform type FRAME: Steel BORE: 6 inches STROKE: 6 inches CYLINDERS: 4, cast separate VALVE ARRANGEMENT: In cylinder heads, operated from one side MOTOR SUSPENSION: Under driver's seat COOLING: Water IGNITION: Jump spark CURRENT SUPPLY: Batteries or magneto CARBURETER: Float-feed type LUBRICATION: Forced feed oiler MOTOR-CONTROL: Spark and throttle CLUTCH: Cast steel bands with graphite inserts CHANGE GEAR: Sliding type SPEEDS: 3 forward and reverse CHANGE-GEAR CONTROL: Side lever DRIVE: Double side chain - Chase 2-Ton Truck, Model I, 30–40 H.P
Chase 2-Ton Truck, Model I, 30–40 H.P. Chase Motor Truck Co., Syracuse, N.Y. PRICE: $3,500 BODY: Express, stake cart or bus CAPACITY: 4,000 pounds WEIGHT: 3,500 pounds WHEEL-BASE: 108 inches TREAD: 56 inches TIRES, FRONT: 36 × 4 in. solid TIRES, REAR: 36 x 3 in. twin solid STEERING: Nut and screw BRAKES: Transmission and rear wheel hub SPRINGS: Front full elliptic, rear semi-elliptic FRAME: Wood BORE: 4½ in.; STROKE: 5 in. CYLINDERS: 4 vertical in front VALVE ARRANGEMENT: 2 cycle; no valves in cylinders MOTOR SUSPENSION: From side of frame COOLING: Forced air IGNITION: Jump spark CURRENT SUPPLY: Storage battery CARBURETER: Automatic LUBRICATION: Automatic MOTOR-CONTROL: Spark and throttle CLUTCH: Cone, cork inserts CHANGE GEAR: Sliding type SPEEDS: 3 forward speeds and reverse CHANGE-GEAR CONTROL: Side lever DRIVE: Side chains - Chicago 6-Ton Coal Truck
Chicago 6-Ton Coal Truck. Chicago Commercial Auto Mfg. Co., Chicago, Ill. BODY: Side delivery CAPACITY: 12,000 pounds WHEEL-BASE: 126 inches TREAD: 64 inches TIRES, FRONT: 36 inches, solid rubber TIRES, REAR: 36 inches, solid rubber STEERING: Vertical column BRAKES: On transmission shaft and rear wheels SPRINGS: Platform type FRAME: Steel BORE: 6 inches STROKE: 6 inches CYLINDERS: 4, cast separate VALVE ARRANGEMENT: In cylinder heads, operated from one side MOTOR SUSPENSION: Under cab COOLING: Water IGNITION: Jump Spark CURRENT SUPPLY: Batteries or magneto CARBURETER: Float-feed type LUBRICATION: Mechanical force feed MOTOR-CONTROL: Spark and throttle CLUTCH: Cast steel bands with graphite inserts CHANGE GEAR: Sliding type SPEEDS: 3 forward and reverse CHANGE-GEAR CONTROL: Side lever DRIVE: Side chains - Chicago 6-Ton Coal Truck
Chicago 6-Ton Coal Truck. Chicago Commercial Auto Mfg. Co., Chicago, Ill. BODY: End delivery CAPACITY: 12,000 pounds WHEEL-BASE: 126 inches TREAD: 64 inches TIRES, FRONT: 36 inches, solid rubber TIRES, REAR: 36 inches, solid rubber STEERING: Vertical column BRAKES: On transmission shaft and rear hubs SPRINGS: Platform type FRAME: Steel BORE: 6 inches STROKE: 6 inches CYLINDERS: 4, cast separate VALVE ARRANGEMENT: In cylinder heads, operated from one side MOTOR SUSPENSION: Under driver's cab COOLING: Water IGNITION: Jump spark CURRENT SUPPLY: Batteries or magneto CARBURETER: Float-feed type LUBRICATION: Mechanical force feed MOTOR-CONTROL: Spark and throttle CLUTCH: Cast steel bands with graphite inserts CHANGE GEAR: Sliding type SPEEDS: 3 forward and reverse CHANGE-GEAR CONTROL: Side lever DRIVE: Side chains - 10-Passenger Limousine
10-Passenger Limousine. Autocar Equipment Co., Buffalo, N. Y. PRICE: $5,500 BODY: Limousine SEATS: 10 persons inside, 2 outside TREAD: 62½ inches TIRES, FRONT: 36 × 3½ in. TIRES, REAR: 36 × 4 in. STEERING: Irreversible with worm gear BRAKES: On counter shaft, and double-acting on rear hubs SPRINGS: Semi-elliptic FRAME: Oak and steel BORE: 411/16 in. STROKE: 5½ in. CYLINDERS: 4 vertical, separate VALVE ARRANGEMENT: On opposite sides COOLING: Water, cellular radiator IGNITION: Jump spark CURRENT SUPPLY: Batteries CARBURETER: Float-feed automatic LUBRICATION: Force feed MOTOR-CONTROL: Spark and throttle CLUTCH: Conical type CHANGE GEAR: Sliding type SPEEDS: 3 forward and reverse CHANGE-GEAR CONTROL: Side lever DRIVE: Double chain - Belden, 30 H.P
Belden, 30 H.P. Belden Auto Co., Pittsburgh, Pa. PRICE: $4,500 BODY: Side entrance tonneau SEATS: 7 persons WEIGHT: 2,450 pounds WHEEL-BASE: 124 inches TREAD: 56 inches TIRES, FRONT: 36 × 3½ inches TIRES, REAR: 36 × 4½ inches STEERING: Worm and sector BRAKES: Two on rear hubs SPRINGS: Semi-elliptical front; platform rear FRAME: Pressed steel BORE: 5⅛ in.; STROKE: 5½ in. CYLINDERS: 4 vertical, in front VALVE ARRANGEMENT: Mechanical intake and exhaust MOTOR SUSPENSION: From side members of frame COOLING: Water; cellular radiator IGNITION: Jump spark CURRENT SUPPLY: Magneto and battery CARBURETER: Automatic LUBRICATION: Force feed MOTOR-CONTROL: Spark and throttle CLUTCH: Multiple disc CHANGE GEAR: Belden selective SPEEDS: 3 forward and reverse CHANGE-GEAR CONTROL: Side lever DRIVE: Shaft - Buggyabout, Model C, 14 H.P
"Buggyabout," Model C, 14 H.P. Hatfield Motor Vehicle Co., Cortland, N. Y. PRICE: $750 BODY: Piano box convertible to commercial wagon SEATS: 4 persons WEIGHT: 900 pounds WHEEL-BASE: 101 inches TREAD: 56 inches TIRES, FRONT: 38 × 1½ inches TIRES, REAR: 42 × 1½ inches STEERING: Chain and sprocket (patented) BRAKES: 2 on differential sprockets, 2 emergency SPRINGS: Full elliptical FRAME: Wood sill, reinforced by angle iron BORE: 4½ in.; STROKE: 4 in. CYLINDERS: 2 opposed VALVE ARRANGEMENT: Automatic intake; mechanical exhaust MOTOR SUSPENSION: From sills COOLING: Air IGNITION: Jump spark CURRENT SUPPLY: Dry cells CARBURETER: Schebler LUBRICATION: Gravity feed MOTOR-CONTROL: Spark and throttle CLUTCH: None SPEEDS: 3 to 25 miles DRIVE: Friction drive (patented) - R & L Stanhope
R & L Stanhope. Rauch and Lang Carriage Co., Cleveland, Ohio PRICE: $1,850 BODY: Stanhope SEATS: 2 persons WEIGHT: 1,600 pounds WHEEL-BASE: 73 inches TIRES, FRONT: 32 in., pneumatic TIRES, REAR: 32 in., pneumatic STEERING: Side lever BRAKES: On rear wheels and emergency SPRINGS: Semi-elliptic front; full elliptic rear FRAME: Steel HORSE-POWER: 1½ MOTOR: Hertner MOTOR SUSPENSION: Under body SPEED: 1–22 m. p. h. DISTANCE: 75 to 80 miles MOTOR-CONTROL: Lever at left of seat DRIVE: Double chain from countershaft - Sovereign, Model M
Sovereign, Model M. Matthews Motor Co., Camden, N. J. BODY: Side entrance tonneau SEATS: 8 persons WHEEL-BASE: 124 inches TREAD: 56 inches TIRES, FRONT: 36 × 4 inches TIRES, REAR: 36 × 5 inches BRAKES: 2 double internal on rear hubs SPRINGS: Semi-elliptic, front; platform type rear FRAME: Pressed steel BORE: 5½ in.; STROKE: 6 in. CYLINDERS: 4 vertical MOTOR SUSPENSION: From frame COOLING: Water IGNITION Jump spark (double plugs) CURRENT SUPPLY: Magneto and batteries CARBURETER: Automatic LUBRICATION: Mechanical pump MOTOR-CONTROL: Spark and throttle CHANGE GEAR: Sliding type SPEEDS: 4 forward and reverse CHANGE-GEAR CONTROL: Side lever DRIVE: Double side chain - Synnestvedt 2-Ton Truck
Synnestvedt 2-Ton Truck. Synnestvedt Machine Co., Pittsburgh, Pa. BODY: Stake or van CAPACITY: 2 tons WHEEL-BASE: 87 inches TREAD: 52 inches TIRES, FRONT: 36 × 4 in. TIRES, REAR: 36 × 5 in. BRAKES: On rear wheel and driving shaft SPRINGS: Platform FRAME: Channel steel MOTOR: Synnestvedt electric MOTOR SUSPENSION: In rear under body SPEEDS: 4 forward, 2 reverse DRIVE: Chain - Hercules, Model 140
Hercules, Model 140. James Macnaughtan Co., Buffalo, N. Y. PRICE: $2,350 BODY: Piano box SEATS: 2 or 4 persons CAPACITY: 1,500 pounds WEIGHT: 3,300 pounds TIRES, FRONT: 36 × 3 inches TIRES, REAR: 39 × 3½ inches STEERING: Irreversible type BRAKES: Internal expanding hub SPRINGS: Full elliptic MOTORS: Double equipment MOTOR SUSPENSION: From body MOTOR-CONTROL: Westinghouse SPEEDS: 4 ahead and reverse DRIVE: Double chain - Hercules, Model 144
Hercules, Model 144. James Macnaughtan Co., Buffalo, N. Y. PRICE: $1,700 BODY: Heavy platform truck CAPACITY: 6,000 pounds WEIGHT: 3,525 pounds WHEEL-BASE: 73½ inches TREAD: 37⅜ inches TIRES, FRONT: 20 × 4 × ⅜ in. steel TIRES, REAR: 20 × 4 × ⅜ in. steel STEERING: Irreversible worm type BRAKES: Electric on motors SPRINGS: No springs MOTORS: Single equipment MOTOR SUSPENSION: From body MOTOR-CONTROL: Westinghouse CHANGE SPEEDS: 3 speeds forward and reverse DRIVE: Double chain - Hill Touring Car, 35 H.P
Hill Touring Car, 35 H.P. Hill Motor Car Co., Haverhill, Mass. PRICE: $3,000 BODY: Side entrance tonneau SEATS: 5 persons WEIGHT: 2,200 pounds TIRES, FRONT: 32 × 4 inches TIRES, REAR: 32 × 4 inches BRAKES: On rear wheel drums SPRINGS: Full elliptic FRAME: Pressed steel BORE: 4½ in.; STROKE: 5 in. CYLINDERS: 4 vertical cast separately VALVES: Mechanically operated MOTOR SUSPENSION: Direct from frame COOLING: Air IGNITION: Jump spark CURRENT SUPPLY: Storage battery CARBURETER: Float-feed automatic LUBRICATION: Automatic MOTOR-CONTROL: Hand or foot CLUTCH: Multiple disc CHANGE GEAR: Sliding type SPEEDS: 3 forward and reverse CHANGE-GEAR CONTROL: Side lever DRIVE: Bevel gear - Hercules, Model 121
Hercules, Model 121. James Macnaughtan Co., Buffalo, N. Y. PRICE: $3,200 BODY: Delivery truck CAPACITY: 4,000 pounds WEIGHT: 6,000 pounds WHEEL-BASE: 103 inches TREAD: 72 inches TIRES, FRONT: 36 × 4 inches TIRES, REAR: 38 × 4 inches STEERING: Pinion and sector type BRAKES: Internal expanding hub SPRINGS: Half platform front and rear MOTORS: Double equipment MOTOR SUSPENSION: From body MOTOR-CONTROL: Westinghouse SPEED: 8½ m.p.h. CHANGE SPEEDS: 4 forward and reverse DISTANCE: 38 miles DRIVE: Double chain NOTE: With slight changes in price and specifications these trucks range in capacity up to 10,000 pounds: bodies to order - Hercules, Model 128
Hercules, Model 128. James Macnaughtan Co., Buffalo, N. Y. PRICE: $4,400 BODY: Stake platform with top CAPACITY: 10,000 pounds WEIGHT: 8,700 pounds WHEEL-BASE: 117 inches TREAD: 83 inches TIRES, FRONT: 36 × 7 inches TIRES, REAR: 36 × 7 inches STEERING: Pinion and sector type BRAKES: Internal expanding hub SPRINGS: Semi-elliptic MOTORS: Double equipment MOTOR SUSPENSION: From body MOTOR-CONTROL: Westinghouse CHANGE SPEEDS: 4 forward and reverse DRIVE: Double chain - Hercules, Model 139
Hercules, Model 139. James Macnaughtan Co., Buffalo, N. Y. PRICE: $2,250 BODY: Express wagon CAPACITY: 2,000 pounds WEIGHT: 3,200 pounds TIRES, FRONT: 34 × 3½ inches TIRES, REAR: 36 × 4 inches STEERING: Horizontal side lever BRAKES: Internal expanding hub SPRINGS: Front, half platform; rear, full elliptic MOTORS: Single equipment MOTOR SUSPENSION: From body DISTANCE: 50 miles MOTOR-CONTROL: Westinghouse SPEED: 9 m.p.h. CHANGE SPEEDS: 4 speeds ahead and reverse DRIVE: Double chain - Hercules, Model 106
Hercules, Model 106. James Macnaughtan Co., Buffalo, N. Y. PRICE: $2,350 BODY: Open delivery CAPACITY: 1,500 pounds WEIGHT: 3,500 pounds WHEEL-BASE: 77 inches TREAD: 65 inches TIRES, FRONT: 36 × 3 inches TIRES, REAR: 39 × 3½ inches STEERING: Irreversible type BRAKES: Internal expanding hub SPRINGS: Front, semi-elliptic; rear, half platform MOTORS: Double equipment MOTOR SUSPENSION: From body MOTOR-CONTROL: Westinghouse CHANGE SPEEDS: 4 forward and reverse DRIVE: Double chain - Hercules, Model 113
Hercules, Model 113. James Macnaughtan Co., Buffalo, N. Y. PRICE: $3,750 BODY: Platform truck CAPACITY: 7,000 pounds WEIGHT: 7,500 pounds WHEEL-BASE: 118 inches TREAD: 70 inches TIRES, FRONT: 36 × 5 inches TIRES, REAR: 38 × 5 inches STEERING: Pinion and sector type BRAKES: Internal expanding hub SPRINGS: Semi-elliptic MOTORS: Double equipment MOTOR SUSPENSION: From body SPEED: 8 m.p.h. MOTOR-CONTROL: Westinghouse DISTANCE: 30 miles CHANGE SPEEDS: 4 forward and reverse DRIVE: Double chain - Hercules, Model 120
Hercules, Model 120. James Macnaughtan Co., Buffalo, N. Y. PRICE: $1,750 BODY: Delivery wagon (closed) CAPACITY: 1,000 pounds WEIGHT: 2,300 pounds TIRES, FRONT: 34 × 2½ inches TIRES, REAR: 36 × 2½ inches STEERING: Side bar BRAKES: Band brakes on rear axle SPRINGS: Front, elliptic; rear, platform MOTORS: Double equipment MOTOR SUSPENSION: From body MOTOR-CONTROL: Westinghouse SPEEDS: 4 speeds ahead and reverse DRIVE: Double chain - Hercules, Model 102
Hercules, Model 102. James Macnaughtan Co., Buffalo, N. Y. PRICE: $2,000 BODY: Delivery wagon (closed) CAPACITY: 800 pounds WEIGHT: 2,576 pounds TIRES, FRONT: 34 × 2 inches TIRES, REAR: 36 × 2 inches STEERING: Horizontal side lever BRAKES: Internal expanding hub SPRINGS: Front, half platform; rear, full elliptical MOTORS: Single equipment MOTOR SUSPENSION: From body MOTOR-CONTROL: Westinghouse SPEED: 12 m.p.h. CHANGE SPEEDS: 4 forward and reverse DISTANCE: 40 miles DRIVE: Double chain - Hercules, Model 103
Hercules, Model 103. James Macnaughtan Co., Buffalo, N. Y. PRICE: $3,000 BODY: Delivery wagon with top CAPACITY: 3,000 pounds WEIGHT: 5,400 pounds WHEEL-BASE: 111 inches TREAD: 65½ inches TIRES, FRONT: 36 × 4 inches TIRES, REAR: 36 × 4 inches STEERING: Irreversible worm type BRAKES: Internal expanding hub SPRINGS: Half platform front and rear MOTORS: Double equipment MOTOR SUSPENSION: From body SPEED: 10 m.p.h. DISTANCE: 45 miles MOTOR-CONTROL: Westinghouse CHANGE SPEEDS: 4 forward and reverse DRIVE: Double chain - Pennsylvania, 35 H.P. Pennsylvania Auto Motor Co., Phil., Pa.
PRICE: $2,800 BODY: Mercedes SEATS: 5 persons WEIGHT: 2,550 pounds WHEEL-BASE: 111 inches TREAD: 56 inches TIRES, FRONT: 34 × 4 in. TIRES, REAR: 34 × 4 in. STEERING: Worm and nut BRAKES: Double on rear wheels SPRINGS: Front, 40 in. long; Rear, platform type FRAME: Pressed steel BORE: 4½ in.; STROKE: 5 in. CYLINDERS: 4 vertical, cast separate VALVE ARRANGEMENT: Same side MOTOR SUSPENSION: Direct from sub-frame COOLING: Water; cellular radiator IGNITION: Jump spark CURRENT SUPPLY: Storage battery CARBURETER: Schebler LUBRICATION: Force feed MOTOR-CONTROL: Spark and throttle CLUTCH: Cone CHANGE GEAR: Sliding type SPEEDS: 3 forward and reverse CHANGE-GEAR CONTROL: Selective system DRIVE: Shaft - Marion Model 7, 22–24 H.P
Marion Model 7, 22–24 H.P. The Marion Motor Car Co., Indianapolis, Ind. PRICE: $2,000 BODY: Runabout SEATS: 2 persons WEIGHT: 1,750 pounds WHEEL-BASE: 100 inches TREAD: 55 inches TIRES, FRONT: 32 × 3½ inches TIRES, REAR: 32 × 3½ inches STEERING: Worm and sector BRAKES: Hub, internal and external SPRINGS: Semi-elliptic front, and full scroll rear FRAME: Pressed steel BORE: 4 in.; STROKE: 4 in. CYLINDERS: 4 separate VALVE ARRANGEMENT: Opposite sides MOTOR SUSPENSION: From side members of main frame COOLING: Water IGNITION: High-tension CURRENT SUPPLY: Storage battery CARBURETER: Schebler or Holley LUBRICATION: Force feed MOTOR-CONTROL: Spark and throttle CLUTCH: Multiple disc CHANGE GEAR: "Hassler" SPEEDS: 2 forward and reverse CHANGE-GEAR CONTROL: Side lever DRIVE: Shaft - Wolfe, Model A, 24 H.P
Wolfe, Model A, 24 H.P. H. E. Wilcox Motor Car Company, Minneapolis, Minn. PRICE: $1,800 BODY: Side entrance, rear seat removable SEATS: 5 persons WEIGHT: 1,900 pounds WHEEL-BASE: 108 inches TREAD: 56 inches TIRES, FRONT: 34 × 3½ inches TIRES, REAR: 34 × 3½ inches STEERING: Worm and sector BRAKES: On rear hubs SPRINGS: Full elliptic FRAME: Pressed steel BORE: 4 in.; STROKE: 4 in. CYLINDERS: 4 vertical, tandem MOTOR SUSPENSION: On sub-frame COOLING: Air IGNITION: Jump spark CURRENT SUPPLY: Battery CARBURETER: Float-feed LUBRICATION: Mechanical force feed MOTOR-CONTROL: Spark and throttle CLUTCH: Cone CHANGE GEAR: Sliding type SPEEDS: 3 forward and reverse CHANGE-GEAR CONTROL: Side lever DRIVE: Side chain NOTE: Runabout body fitted to above chassis for a list of $1,700. Light delivery body also furnished on order. - Buggyabout, Model C, 14 H.P
"Buggyabout," Model C, 14 H.P. Hatfield Motor Vehicle Co., Cortland, N. Y. PRICE: $750 BODY: Piano box convertible to commercial wagon SEATS: 4 persons WEIGHT: 900 pounds WHEEL-BASE: 101 inches TREAD: 56 inches TIRES, FRONT: 38 × 1½ inches TIRES, REAR: 42 × 1½ inches STEERING: Chain and sprocket (patented) BRAKES: 2 on differential sprockets, 2 emergency SPRINGS: Full elliptical FRAME: Wood sill, reinforced by angle iron BORE: 4½ in.; STROKE: 4 in. CYLINDERS: 2 opposed VALVE ARRANGEMENT: Automatic intake; mechanical exhaust MOTOR SUSPENSION: From sills COOLING: Air IGNITION: Jump spark CURRENT SUPPLY: Dry cells CARBURETER: Schebler LUBRICATION: Gravity feed MOTOR-CONTROL: Spark and throttle CLUTCH: None SPEEDS: 3 to 25 miles DRIVE: Friction drive (patented) - Aurora, Model 'A,' 14–16 H.P
Aurora, Model "A," 14–16 H.P. Aurora Motor Works, North Aurora, Ill. PRICE: $650 BODY: Runabout body SEATS: 2 passengers WEIGHT: 1,000 pounds WHEEL-BASE: 80 inches TREAD: 56 inches TIRES, FRONT: 34 × 2 inches TIRES, REAR: 34 × 2 inches STEERING: Wheel steer; pinion gear BRAKES: Rear hub band brakes and transmission brakes SPRINGS: Half elliptical, front; full elliptical, rear FRAME: Angle steel BORE: 4½ in.; STROKE: 4 in. CYLINDERS: Double opposed horizontal, under hood VALVE ARRANGEMENT: Inlet and exhaust on opposite sides of motor MOTOR SUSPENSION: 3 point suspension COOLING: Water; triangular tube special radiator; thermo-siphon IGNITION: Jump spark CURRENT SUPPLY: Dry batteries CARBURETER: Holly LUBRICATION: Automatic force feed MOTOR-CONTROL: Spark and throttle on steering column CLUTCH: Cone CHANGE GEAR: Planetary transmission SPEEDS: 2 forward and 1 reverse CHANGE-GEAR CONTROL: Side lever DRIVE: Shaft driven - Waltham-Orient, Model B R., 4 H.P
Waltham-Orient, Model B R., 4 H.P. Waltham Mfg. Co., Waltham, Mass. PRICE: $400 BODY: Runabout SEATS: 2 persons WEIGHT: 600 pounds WHEEL-BASE: 80 inches TREAD: 42 inches TIRES, FRONT: 26 × 2½ in. TIRES, REAR: 26 × 2½ in. STEERING: Tiller BRAKES: On rear hubs SPRINGS: Elliptical front and rear FRAME: Wood BORE: 3¼ in.; STROKE: 4¼ in. CYLINDERS: One in back VALVE ARRANGEMENT: Automatic inlet; mechanical exhaust MOTOR SUSPENSION: Rear on side members of frame COOLING: Air IGNITION: Jump spark CURRENT SUPPLY: Dry battery CARBURETER: Orient LUBRICATION: Oil pump MOTOR-CONTROL: Throttle and spark CLUTCH: Friction CHANGE GEAR: Friction SPEEDS: 5 forward, 2 reverse CHANGE-GEAR CONTROL: Side lever DRIVE: Friction drive NOTE: Furnished with 2 cylinder motor for $50 extra. - Albany Run-a-bout, Model 2, 4–6 H. P
Albany Run-a-bout, Model 2, 4–6 H. P. Albany Automobile Co., Albany, Ind. PRICE: $300; with top BODY: Piano box SEATS: 2 persons WEIGHT: 500 pounds WHEEL-BASE: 62 inches TREAD: 52 inches TIRES, FRONT: 30 × 1¼ in., solid TIRES, REAR: 32 × 1¼ in., solid STEERING: Hand lever or tiller BRAKES: Foot brake on transmission SPRINGS: Full elliptic FRAME: Angle steel BORE: 4½ in.; STROKE: 4 in. CYLINDERS: 1, vertical, in front VALVE ARRANGEMENT: 3 port, side valves MOTOR SUSPENSION: From side members of frame COOLING: Water; pump IGNITION: Jump spark CURRENT SUPPLY: Dry battery CARBURETER: Universal; automatic mixture regulation LUBRICATION: Sight feed pressure MOTOR-CONTROL: Spark and throttle TRANSMISSION: Friction CHANGE SPEEDS: Slide of friction disk SPEEDS: 2 to 10 miles and reverse CHANGE-SPEED CONTROL: Side lever DRIVE: Center chain on differential sprocket - C. P. R. grain elevator at Fort William, Ontario
The farmer sells his crop of wheat to the grain-dealer, and carts it, say, to Brandon, where the purchaser takes delivery of it at his elevator. Let us examine this thing somewhat minutely, taking by way of illustration one of the elevators belonging to the Canadian Pacific Railway Company at Montreal. It is a medium-sized one, having capacity for storing about 600,000 bushels of grain. The same company’s elevators at Fort William and Port Arthur are much larger, having capacity for 1,500,000 bushels. In Chicago and Buffalo there are elevators of three millions of bushels capacity; but, whether larger or smaller, in their main features they are all alike. The elevator is a wooden structure of great strength. Its massive stone foundations rest on piles imbedded in concrete. The framework is so thoroughly braced and bolted together as to give it the rigidity of a solid cube, enabling it to resist the enormous pressure to which it is subjected when filled with 18,000 tons of wheat. The building is 210 feet long, 80 feet wide, and 142 feet in height from basement to the peak of the roof. Including the steam-engine (built at the C. P. R. works) of 240 horse-power, the entire cost of this elevator was $150,000. It consists of three distinct compartments—for receiving, storing, and delivering grain. On the ground floor are two lines of rails by which the cars have ingress and egress. The general appearance of this flat is that of a bewildering array of ponderous posts and beams, shafting, cog-wheels, pulleys and belts, blocks and tackle, chutes, and the windlasses for hauling in and out the cars, for a locomotive with its dangerous sparks may not cross the threshold. Beneath this, in the basement, are the receiving tanks, thirty-five feet apart from centre to centre, corresponding to the length of the cars. Of these there are nine, enabling that number of cars to be simultaneously unloaded. This is quickly done by a shovel worked by machinery, with the aid of two men, the grain falling through an iron grating in the floor into the tank. The elevator has nine “legs.” The leg is an upright box, 12 inches by 24 inches, extending from the bottom of the tank to the top of the building; inside of it is a revolving belt with buckets attached 15½ inches apart. The belt is 256 feet long, and as it makes 36 revolutions per minute, each bucket containing one-third of a bushel, each leg is able to raise 5,250 bushels per hour. A car is unloaded and its contents hoisted into the upper regions in fifteen minutes. When all the legs are at work 30,000 bushels are handled in an hour. - The tunnels
The tunnels are passages for trains under mountains, hills and rivers. The tunnels are dark but the trains are well lighted. Electric motors are often used, this avoids the smoke of steam engines which is very unpleasant in the tunnels. - The Stage coach
The Stage coach is used in the country where towns are few. The stages meet trains at the stations and take on passengers to be carried to their homes away from the railroad. Some of the stage routes are several hundred miles long. - The Train Ferry
The Train Ferry carries entire trains across rivers where there are no bridges. Some of the largest train boats have several tracks and carry a train on each. The boats are tied in slips at the shore so that the tracks meet exactly those on the land. - An observation train
An observation train is often made up to follow the great college boat races, where the railroad runs along the river bank. Flat cars are used with seats fixed on them for the spectators. - The water tank
The water tank is seen frequently along the route of the railroads and plenty of water must be taken on and carried in the engine tender to make steam which is the power used to drive the big engines. - The Round House
The Round House is the place where the railroad engines are kept when they are not working. The engines are turned around on a big turn table so each can be run on the different tracks which all lead to the turn-table in the centre. - Horses in a heap, Leader down, Wheelers falling over him
I have twice had three out of the four horses in a heap, from a leader coming down and the two wheelers falling over him; but in such a case as this there is very little danger if the coachman has the presence of mind not to leave his box till there is sufficient strength at the horses' heads to prevent them jumping up and starting off frightened. - A kafila of slaves
A kafila (caravan) of slaves - La France
One of the largest sailing-ships afloat is the French five-master, La France, launched in 1890 on the Clyde, and owned by Messrs A. D. Bordes et Fils, who possess a large fleet of sailing-vessels. In 1891 she came from Iquique to Dunkirk in one hundred and five days with 6000 tons of nitrate; yet she was stopped on the Tyne when proceeding to sea with 5500 tons of coal, and compelled to take out 500 tons on the ground that she was overladen. - A Stage Coach of the Eighteenth Century
A Stage Coach of the Eighteenth Century - Washington's Coach
We must remember that travelling was no such simple and easy matter then as it is now. As the planters in Virginia usually lived on the banks of one of the many rivers, the simplest method of travel was by boat, up or down stream. There were cross-country roads, but these at best were rough, and sometimes full of roots and stumps. Often they were nothing more than forest paths. In trying to follow such roads the traveler at times lost his way and occasionally had to spend a night in the woods. But with even such makeshifts for roads, the planter had his lumbering old coach to which, on state occasions, he harnessed six horses and drove in great style. - Telegraph and Railroad
Telegraph and Railroad - The Clermont
The Clermont Fulton returned in 1806 to America, where, with money furnished by his friend Livingston, he began to construct another steamboat which he called the Clermont, after the name of Livingston's home on the Hudson. This boat was 130 feet long and 18 feet wide, with a mast and a sail, and on each side a wheel 15 feet in diameter, fully exposed to view. One morning in August, 1807, a throng of expectant people gathered on the banks of the North River at New York, to see the trial of the Clermont. Everybody was looking for failure. People had all along spoken of Fulton as a crack-brained dreamer, and had called the Clermont "Fulton's Folly." "Of course the thing would not move." "That any man with common-sense might know," they said. So while Fulton was waiting to give the signal to start, these wiseacres were getting ready to jest at his failure. Finally, at the signal, the Clermont moved slowly, and then stood perfectly still. "Just what I have been saying," said one onlooker with emphasis. "I knew the boat would not go," said another. "Such a thing is impossible," said a third. But they spoke too soon, for after a little adjustment of the machinery, the Clermont steamed proudly up the Hudson. - A Flat Boat
A Flat Boat Another illustration of his [Robert Fulton] inventive gift belongs to his boyhood days. He and one of his playmates used to go out fishing in a flat boat which they propelled by the use of long poles. Getting tired of this method of navigation, Robert made two crude paddle-wheels, one for each side of the boat, connecting them by a sort of double crank, which the boys united in turning. They could then easily propel the boat in their fishing trips to various parts of the lake, and keenly enjoyed this novel and easy way of going a-fishing. - A Pack Horse
A Pack Horse - A Porter carrying goods
A Porter carrying goods - A Sedan Chair
The vehicles of this description are nearly as various in the different provinces of China, and among the different ranks of inhabitants, as their boats and barges are. The one here engraved belongs to a person in a certain `rank` of life, probably an inferior mandarin. It will be observed that, instead of carrying the poles in the hands, as we do, the Chinese carry the chairs on the shoulders by means of a cross-bar fixed to the poles by straps: but different kinds of chairs are carried in different ways. - A waterman in his barge
Some millions of Chinese live entirely on the water, in boats and barges of various kinds, some occupied in carrying articles of provisions and merchandize, others in conveying passengers, some in feeding and rearing ducks, and others in fishing. Some of these vessels have masts and sails, others are forced forwards with large sculls or pushed on with poles, some are dragged along by men, and others, but very rarely, by horses. Near the head of each vessel is suspended in some convenient place, one of those noisy instruments well known in this country by the name of gong, which is used to regulate the motions of the trackers, and to give notice to other vessels of the approach and intentions of the one that beats the signal. - View on the Great Canal
The grand canal of China, or rather the water communication between the northern and southern extremities of the empire by a succession of canals and rivers, is certainly the first inland navigation in the world. The multitude of vessels, of every size and shape, is not to be estimated. The large one in the print is one of those which carried the British embassador and his suite up the Pei-ho to the neighbourhood of Pekin, which were in every respect comfortable and commodious. On passing bridges, which are very frequent in the neighbourhood of all towns and villages, the masts are usually lowered down; but many of the bridges are lofty enough to admit the smaller kind of barges to pass underneath with their masts standing. The bridges are almost as various in their shape and construction as the barges, and some of them by no means destitute of taste. - A Chinese Carriage
This machine, like a baker’s cart, is the kind of wheel carriage which is most common in the country, and such as even the high officers of state ride in, when performing land journies in bad weather, and the driver invariably sits on the shaft in the aukward manner here represented. They have no springs, nor any seat in the inside, the persons using them always sitting cross-legged on a cushion at the bottom. In these carts the gentlemen of Lord Macartney’s embassy who had not horses, were accommodated, over a stone pavement full of rutts and holes. When ladies use them, a bamboo screen is let down in front to prevent their being stared at by passengers, and on each side, the light is admitted through a square hole just large enough for a person’s head.